technical data sheet calibration adaptor rpc-3.50 jack C p-smp jack 03K119-K20S3 rosenberger hochfrequenztechnik gmbh & co. kg p.o.box 1260 d-84526 tittmoning germany www.rosenberger.de tel. : +49 8684 18-0 email : info@rosenberger.de page 1 / 3 rf_35/09.14/6.2 dieses dokument ist urheberrechtlich geschtzt this document is protected by copyright rosenberger hochfrequenztechnik gmbh & co. kg all dimensions are in mm; tolerances according to i so 2768 m-h interface rpc-3.50 according to iec 60169-23 rpc-3.50 mechanically compatible with rpc-2.92 and sma p-smp according to rosenberger p-smp standard documents application note an001 calibration services material and plating connector parts material plating center conductor cube gold, min. 1.27 m, over nick el outer conductor rpc-3.50 stainless steel passivated outer conductor p-smp cube gold, min. 1.27 m, over nickel dielectric ps
technical data sheet calibration adaptor rpc-3.50 jack C p-smp jack 03K119-K20S3 rosenberger hochfrequenztechnik gmbh & co. kg p.o.box 1260 d-84526 tittmoning germany www.rosenberger.de tel. : +49 8684 18-0 email : info@rosenberger.de page 2 / 3 rf_35/09.14/6.2 dieses dokument ist urheberrechtlich geschtzt this document is protected by copyright rosenberger hochfrequenztechnik gmbh & co. kg electrical data frequency dc to 26.5 ghz return loss 3 32 db, dc to 4 ghz 3 28 db, 4 ghz to 10 ghz 3 23 db, 10 ghz to 18 ghz 3 19 db, 18 ghz to 26.5 ghz mechanical data rpc-3.50 p-smp mating cycles 3 500 3 100 if mating part is full detent 3 500 if mating part is limited detent 3 1000 if mating part is smooth bore maximum torque 1.70 nm recommended torque 0.90 nm engagement force full detent 68 n limited detent 45 n smooth bore 10 n disengagement force full detent 25 n limited detent 15n smooth bore 2.2 n gauge 0.00 mm to 0.08 mm 0.00 mm to 0.08 mm general standard definition for proper operation the vector network analyzer (v na) needs a model describing the electrical behavio ur of this calibration standard. the different models, units, and terms used will depend on the vna type and they will have to be entered into the vna. all values ar e based on typical geometry and plating. offset z o / impedance / z o 50 w offset delay 63.0641 ps length (electrical) / offset length 18.90 mm offset loss 2.51 g ? /s loss 0.0137 db/ ghz environmental data operating temperature range 1 +20 c to +26 c rated temperature range of use 2 0 c to +50 c storage temperature range -40 c to +85 c rohs compliant 1 temperature range over which these specifications a re valid. 2 this range is underneath and above the operating te mperature range, within the calibration adaptor is fully functional and could be used without damage.
technical data sheet calibration adaptor rpc-3.50 jack C p-smp jack 03K119-K20S3 rosenberger hochfrequenztechnik gmbh & co. kg p.o.box 1260 d-84526 tittmoning germany www.rosenberger.de tel. : +49 8684 18-0 email : info@rosenberger.de page 3 / 3 rf_35/09.14/6.2 dieses dokument ist urheberrechtlich geschtzt this document is protected by copyright rosenberger hochfrequenztechnik gmbh & co. kg declaration of calibration options factory calibration standard delivery for this calibration standard inc ludes a factory calibration. the calibration certif icate issued reports individual calibration results, traceable to rosenberger standards , national / international standards are not available. model based standard d efinitions are reported in an agilent/keysight, rohde & schwarz and anritsu compatible vna format. accredited calibration not available. for further, more detailed information see applicat ion note an001 on the rosenberger homepage. calibration interval recommendation 12 months packing standard 1 pce in box weight 5.3 g/pce draft date approved date rev. engineering change n umber name date herbert babinger 13.10.10 herbert babinger 25/04/16 c00 14-1492 m.ruf 25/04/16 while the information has been carefully compiled t o the best of our knowledge, nothing is intended as representation or warr anty on our part and no statement herein shall be construed as recommendation to infringe existing patents. in the effort to improve our products, we reserve the right to make changes judg ed to be necessary.
|
